| |
| DiSEqC Installation: |
| |
| With the addition of a digital MPEG-2/DVB receiver as a slave, you could still utilize your existing movable C / Ku band dish and analog receiver system or 4Dtv IRD. As the master receiver, the analog receiver is used for the reception of analog C and Ku band programming, and also to position the antenna and select the correct polarization of the feed horn. The digital DVB channels will be viewed using the DVB receiver. |
| |
| Most MPEG-2/DVB receivers have one LNB input, so you will need the kit to switch C or Ku feed from your dish. All digital receivers sold here offer DiSEqC, 0-12V, and 22Khz Tone switching control output. |
| |
|
The basic slave kit accessories you will need are:
- 1 x Auto 0/22kHz, A/B, 0/12V switch, or 2 way DiSEqC switch
- 2 x high frequency splitters (one leg DC-pass)
- 5 x 3' coax patch RG-6 cables
|
| |
|
|
| |
| Procedures: |
| |
- Connect the C band coax from dish to one splitter input
- Connect the Ku band coax from dish to the second splitter input.
- Connect both DC pass outputs from the splitters to the C and Ku LNB inputs on your old analog/4DTV receiver.
- Connect the other two remaining outputs from splitters to the 0/22kHz switch's two inputs. C side to "0Hz" input, and Ku side to "22kHz"
- The single output from 0/22kHz switch goes directly to the DVB receiver LNB (IF) input.
|
| |
| Specific instructions for the Satcruiser DSR-101Plus LNB switch setup: |
| |
-
From the Installation menu, select the LNB Power menu. LNB power must be ON.
-
From the Installation menu, select TP configuration.
-
In the LNB Configuration menu, set:
|
| |
|
Satellite Type
|
C Band |
Ku Band |
|
LNB Type
|
Standard |
Standard |
| LO Freq. |
5150 |
10750 |
| LO. Freq. low |
|
|
| 22KHz |
OFF |
OFF |
| DiSEqC |
DiSEqC1 |
DiSEqC2 |
| Mode |
OFF |
OFF |
| DiSEqC 1.2 |
Disable |
Disable |
| 0/12V Switch |
|
|
|
|
For 2 Way DiSEqC Switch
|
| |
|
Satellite Type
|
C Band |
Ku Band |
|
LNB Type
|
Standard |
Standard |
| LO Freq. |
5150 |
10750 |
| LO. Freq. low |
|
|
| 22KHz |
OFF |
ON |
| DiSEqC |
Disable |
Disable |
| Mode |
OFF |
OFF |
| DiSEqC 1.2 |
Disable |
Disable |
| 0/12V Switch |
|
|
|
|
For Auto 0/22kHz Switch
|
|
|
|
Satellite Type
|
C Band |
Ku Band |
|
LNB Type
|
Standard |
Standard |
| LO Freq. |
5150 |
10750 |
| LO. Freq. low |
|
|
| 22KHz |
OFF |
OFF |
| DiSEqC |
Disable |
Disable |
| Mode |
OFF |
OFF |
| DiSEqC 1.2 |
Disable |
Disable |
| 0/12V Switch |
0V |
12V |
|
|
For Auto 0/12V Switch
|
| |
|
Copyright 2007 Satpros Corp., All Rights Reserved.
|
